Produktai skirti prekės grąžinimo atostogų metu (363)

TECHNICAL DETAILS Powder filler for all types of interior filling work on uneven substrates. SEMIN HIGH BUILD FILLER has very good filling properties. SUITABLE SURFACES All types of interior surfaces: bubbled concrete, untreated concrete, cellular concrete, irregular plaster, heating ceiling, terracotta tiles, uneven substrates... Covering After the filler has dried completely, suitable for covering with all types of plaster-based coatings, thick coatings, wall paper paste, wall coverings. REFERENCE DOCUMENTS • Filler complies with standard NFT 30 608 • DTU 59.1 : painting work • Technical notice CSTB N°9/99-681 TECHNICAL CHARACTERISTICS • Granulometry : up to 0.5 mm • Adhesion : complies with NFT 30 608 • pH : neutral • Usage time for batch : 24 hours PACK SIZE 25 kg bags on shrink-wrapped pallet. APPLICATION May be applied manually with a smoothing trowel or coating blade, or mechanically by spraying then manual smoothing. THICKNESS OF APPLICATION Up to 5 mm in one pass.

TECHNICAL DEFINITION CE 78 PERFECT’LIGHT is a ready-to-use lightweight jointing compound specially formulated for tapered-edge plasterboards, to be used with joint tape. COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightening fillers, preservative and various admixtures. The compound is white. SUITABLE SURFACES All types of tapered-edge, paper-lined plasterboard, with or without insulation. TECHNICAL CHARACTERISTICS • Tape adherence : > 1000 g • Cracking : no cracking up to a thickness of 5 mm APPLICATION Before treating the joints themselves, any gaps where the plasterboards are accidentally out of alignment must be filled, along with any other gaps Apply the product manually, spreading the diluted mixture for 10 or 15 cm with a coating knife before applying the tape (with the rough side against the coating). Then apply a finishing layer, leave to dry and finish to hide the tape and screw heads. In the event of projecting vertical angles, use reinforced tape.

TECHNICAL DETAILS Powder filler for all types of interior filling work on uneven substrates (rough precast concrete, for instance). COMPOSITION AND APPEARANCE Plaster-based powder coating containing calcium carbonate, resin and various additives. The mixed paste is white in colour. SUITABLE SURFACES Interior walls and ceilings: Bubble concrete, bare concrete, cellular concrete, irregular plaster, heating ceiling, uneven surfaces, etc. OVERLAYING After the filler has dried completely, suitable for covering with all types of plaster-based coatings, thick coatings, wall paper or wall coverings. TECHNICAL CHARACTERISTICS • Granulometry : Up to 0.2 mm • Adhesion : complies with NFT 30 608 • pH : neutral PACK SIZE 5 and 25 kg bags on shrink-wrapped pallet. STORAGE 9 months in unopened original packaging stored away from moisture. PREPARATION OF SURFACES Surfaces must comply with DTU 59.1, i.e. be clean, dry, dust-free and free from all traces of form oil.

Equipement en ligne dans un process de production Mesure de longueur ou tout autre contrôle Séparation des produits hors tolérance

DESCRIPTION Coating to quickly fill all sizes of cracks, holes and grooves with no shrinkage and no cracking. COMPOSITION AND APPEARANCE Plaster-based powder filler, calcium carbonate, mineral reducer, cellulose derivatives and various admixtures. The compound obtained is white in colour. SUITABLE SURFACES All types of internal unfinished or painted surfaces : plaster, plasterboard, plaster blocks, concrete, cement coating, breeze blocks, cellular concrete, bricks, terracotta... TECHNICAL CHARACTERISTICS • pH: neutral • Setting time : 30 minutes depending on the ambient conditions and the thickness applied PACKAGING 5 kg and 15 kg bags. APPLICATION To be applied using a coating knife. Amount required : 1 kg m²/mm thickness. DRYING TIME Depends on the ambient conditions, the nature of the surface and the thickness of application. Generally speaking, when spread to a thickness of one cm, the filler dries in 6 hours.

Développement d'outillage ou de machines spéciales Poinçonnage - soudure - découpe - mesure - contrôle

TECHNICAL DEFINITION Cement-based powder filler with fibres for treating damaged exterior substrates. The filler is multi-purpose: can be used to fill, repair and rectify wall surfaces, with a smooth finish. SUITABLE SUBSTRATES All types of substrates : cement, concrete, concrete blocks, stones, brick, old paintwork, old tiling. COVERINGS Once the filler is completely dry, can be covered with all types of coatings and paintwork. Do not directly cover with solvent-borne paint. TECHNICAL FEATURES • Setting time: 30 to 40 minutes • Adhesion: complies with EN 16566 • AFNOR NFT 36.005 classification: Family IV class 4c MIXING PROPORTIONS • 6 to 6.5 litres of water per 15 kg bag • 2 to 2.2 litres of water per 5 kg bag • 0.4 - 0.43l of water for 1 kg • 2 volumes of water for 5 volumes of powder APPLICATION Application with a plastering spatula, knife, smoothing trowel. Clean tools with water. COVERAGE Approximately 1 kg per m²/mm of thickness.

Postes à plateaux tournants indexés - chargement manuel ou automatique - fonctions automatisées et protégées (assemblage, rivetage, sertissage, soudure, contrôle, mesure, marquage, ...) - calcul de la répartition de la charge des stations de travail et du temps menant. En adéquation avec vos produits, voici quelques exemples qui peuvent être proposés : - Station de chargement des pièces, manuel ou automatique (alimentation des composants par trémies, bols vibrants, séparateurs, robot, …) - Station(s) de travail sur les composants (positionnement, soudure, sertissage, vissage, rivetage, collage …) - Station(s) de contrôle sur les pièces : ( vision, mesure, test étanchéité, continuité …) - Stations de conditionnement (regroupement, mise en sachet, mise en carton, etc…) - Station de déchargement manuel ou automatique - Liaisons avec machines en aval ou poste de conditionnement et emballage par exemple.

Relevés sur site - Reconception de machine - amélioration continue - intégration de nouvelles technologies ou nouvelles fonctions Transformation d'un massicot tri-lames Müller Martini, pour conversion en massicot "coins ronds" à 5 500 coupes/heure, avec passage des brochures à l'unité ou empilées par 2. Modélisation sur CAO d'après matériels existants. Reconstruction, avec modifications des fonctions. Intégration de fonctions de sécurité. Intégration de nouvelles fonctions sur une ligne de production. Modification d'automatismes. Retrofit d'actionneurs et d'armoires électriques.

TECHNICAL DEFINITION Ready-to-use, solvent-free adhesive primer for smooth or hardly porous substrates, for interior and exterior use. BETON HAFTGRUND allows to achieve an adhesive bridge between such substrates and certain cementor plaster-based products with a relatively low bond. COMPOSITION AND APPEARANCE Pink, ready-to-use primer with visible grain. Paintlike consistency. ACCEPTED SUBSTRATES Can be applied onto interior and exterior walls, and also onto ceilings. • Smooth cast-in-place concrete • Self-levelling concrete • Old paintwork • Old painted fibreglass coverings APPLICATION BETON HAFTGRUND is to be applied using a brush or a woollen roller. Apply a liberal coat onto the substrate and allow to dry before covering. The drying time will depend on the substrate and ambient conditions. As a general rule, allow for approximately 6 hours.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Smoothing coating. TECHNICAL SPECIFICATIONS - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Density: 1.7 - Reaction to fire: A2s1d0 MIXING RATIO 10 to 11 liters of water per 25 kg bag. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads. Apply a strip by picking up the ceiling, making sure that the concrete is free of any trace of form oil.

COMPOSITION AND APPEARANCE Plaster-based powder coating containing calcium carbonate, resin, cellulose fibre and various additives. The mixed paste is white in colour. REFERENCE DOCUMENTS • DTU 25.41. Standard DIN 1168 • DTU 59.1: painting work • NF EN 13963 TECHNICAL CHARACTERISTICS • Granulometry: fine • Adhesion: complies with NFT 30 608 • pH: neutral APPLICATION • SEALING PLASTERBOARDS WITH ROUNDED EDGES Apply a first pass by filling the joint deeply, apply a second pass after 1 1/2 hours to smooth and finish the joint. Filling and bonding (if tape) in one pass. And finishing is possible in a single layer. • FILLING, ASSEMBLY, SEALING Dilute with 45% water. 2.2 l to 2.3 l water per 5 kg bag or 11 l to 11.5 l for 25 kg. Open bevelled cracks or rifts. Apply with a putty knife or spatula. Completely fill up the part to be filled, smooth carefully. Time of use: 45 min. Hardening: approx. 1 hour.

COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightening fillers, preservatives and various adjuvants. The resulting paste is white in color. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Smoothing coating. TECHNICAL CHARACTERISTICS - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Density: 1.2 STORAGE 9 months in original unopened packaging, protected from frost and heat. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings). The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip in place. Then carry out a finishing pass, let dry and finish to mask the strip. For vertical protruding corners, use a reinforced strip or a metal angle iron.

TECHNICAL DEFINITION CE 78 PERFECT’JOINT is a ready-mix paste specially formulated for jointing mitred-edge plasterboards in association with plaster tape. COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, thickener, pre- servation agent and various adjuvants. The paste is white. SUITABLE SURFACES All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with mitred edges and carded surfaces. COVERINGS Plasterboard primer. Smoothing filler. REFERENCE DOCUMENTS • CE marking • DTU 25.41 and DTU 25.42 • NF EN 13963 • DoP PACK SIZE 7 and 25 kg buckets. STORAGE 12 months in original unopened packaging away from frost and high temperatures. APPLICATION Before actual jointing, fill any accidental gaps between boards and any other areas (spalls, deterioration of the surface etc.). Apply manually by «buttering» the mitred-edge using a 10 or 15 cm plaster spatula and then ad- ding the tape (milled face against the jointing coa- ting).

TECHNICAL DEFINITION Ready mixed filler for interior and exterior finishing work on walls and ceilings OSCAR is a water based filler giving a finish identical to oil based products. COMPOSITION AND APPEARANCE Resin emulsion containing calcium carbonate, rheological agent and various additives. The resulting paste is white. ACCEPTED SUBSTRATES Interior walls and ceilings • Plasterboard • Old paint • Plaster blocks • Primers Outside walls • Smooth concrete • Fine floated cement SUITABLE SURFACES • Wallpaper • Paint • Wall coverings • Thick plastic covering (RPE) TECHNICAL CHARACTERISTICS • Paste density : 1.9 • Particle size : very fine • pH : 7 APPLICATION Application is manual using a float or a painter’s knife. The maximum thickness will be 1 mm per coat. Smooth and sand if necessary before OSCAR has entirely set. Clean tools with water.

TECHNICAL DEFINITION CE 78 PERFECT’LISS is a ready-to-use lightweight compound specially formulated for finishing interior substrates (walls and ceilings). COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightening fillers, preservative and various admixtures. The compound is white. SUITABLE SURFACES Plasterboard, plaster, AAC, brick, fibreglass cloth, gypsum block, concrete, render, old paint. APPLICATION Roller, trowel or airless applications of the product are possible. For roller application, the product should be mixed before use. Nozzles recommended for airless application : 35 and 41. AMOUNT REQUIRED Depends on the thickness applied : from 0.4 to 2 kg/m². DRYING TIME The second coat can be applied 6-24 hours after the first, depending on the ambient conditions.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. The paste obtained is white in color. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 2 hours - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick STORAGE 9 months in original unopened packaging protected from humidity APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings. The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads.

TECHNICAL DEFINITION Multi-purpose filler for interior use. • Filling holes, cracks, chases • Fixing and bedding • Pasting polystyrene, roses, cornices • Finishing COMPOSITION AND APPEARANCE Powder filler composed of plaster, calcium carbonate, resin, cellulose fibre and various additives. Produces a white paste. ACCEPTED SUBSTRATES All types of interior substrates: plaster, plasterboards, plaster blocks, concrete, cement rendering,concrete blocks, aerated concrete, brick, earthenware, TECHNICAL CHARACTERISTICS • Grain size : fine • Adhesion : complies with standard NFT 30 608 • pH : neutral • Setting starts after 50 minutes • Setting ends in 1 hr 10 min • Bending : 3 N/mm2 • Compression : 7 N/mm 12 kg buckets on wrapped pallet. STORAGE 9 months in original unopened packing protected from damp. THE TEMPERATURE DURING APPLICATION AND DRYING MUST BE SUPERIOR TO 5°C. DO NOT USE ON A DAMP SUBSTRATE. DO NOT USE ONCE THE PASTE HAS STARTED TO SET.

TECHNICAL PROPERTIES Primer filler for vertical surfaces or for use on ceilings made from poured concrete or pre-slabs. Decorating filler, for smoothing over. Smooth, matt finish. Odour-free. COMPOSITION AND APPEARANCE. Solvents : Water. Filler : Calcium carbonates. Additives : Dispersing agent, bactericidal fungicide. Thickeners : Cellulosic, polyacrylates. Binders : Acrylic dispersing agent. Density : 1.86. Dry matter : 75%. TECHNICAL PROPERTIES • Fire classification: A2-S1, d0 SUITABLE SURFACES Interior : ideal for covering bricks, brick tiles, cement breeze blocks, cinder blocks, de-bubbling pre-slabs, shuttered concrete, aerated concrete, for redecorating stippled walls or old damaged surfaces. APPLICATION. • The first coat should be levelled out using 60 cm scraper or skimmed with a rule. • After drying, the second coat should be smoothed with a scraper. • After allowing to set slightly, squeeze the filler at a slight angle using a clean scraper.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 4 hours - Adhesion of the tape: > 1000 g - Density: 0.9 - Reaction to fire: A1 STORAGE 9 months in original unopened packaging protected from humidity. RATE OF MIXING 10 to 11 liters of water per 25 kg bag. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings. The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads.

TECHNICAL DEFINITION FIBRELASTIC is a ready-to-use filler paste with a high proportion of resin and glass fibre. Particularly suitable for all types of interior and exterior filling jobs. It has permanent flexibility allowing it to tolerate flexing of the substrate without cracking and it eliminates the need for repair tape. COMPOSITION AND APPEARANCE Emulsion resin, calcium carbonate, fibreglass and various additives. The paste is off-white. ACCEPTED SUBSTRATES • Plaster • Masonry • Cellular concrete • Wood • Cement render • Plasterboard • Roughcast • Old painted surfaces • Concrete • Silico-limestone brick SUITABLE SURFACES Once it has dried entirely FIBRELASTIC can be covered with any type of paint or plaster base or ready-to-use fillers. TECHNICAL CHARACTERISTICS • Viscosity (BV 1000 / 30 rpm) : 300000 mPas • Density : 1.3 • pH : 6 • Permanent elasticity PACK SIZE Tubes containing 300 g. Tubs containing 1.5 and 5 kg.

TECHNICAL DEFINITION Ready-to-use surface filler paste for filling interior holes and cracks. COMPOSITION AND APPEARANCE Water, calcium carbonate, sand, resin and various additives. SUITABLE SUBSTRATES All types of interior substrates : concrete, cellular concrete, cement, breeze block, brick, plasterboard, plaster tiles, plaster, old paint. COVERING Primer coat, smooth surface filler, wall coverings, paint REFERENCE DOCUMENTS • Filler meets EN 16566 standard • DTU 59.1 : Paint work TECHNICAL CHARACTERISTICS • Density : 1.5 • Dry extract : 82 % STORAGE 9 months in original unopened packaging away from frost and high temperatures. PREPARATION OF SUBSTRATES Substrates must comply with the DTU 59.1 standard i.e. be dry, clean, dust-free, hard and free of any trace of separating agent. APPLICATION Applied by hand using a filling knife or spatula. The thickness is 2 cm; to fill deeper holes, build up the filler in several steps The maximum thickness will be 1 cm per coat.

TECHNICAL DEFINITION SEMIN AIRLESS 3 IN 1 is an indoor filler that can be used as an Airless spray. It provides an even appeareance without smoothing, has great coverage and a deep matt finish. It combines 3 actions : underlayer, filler and finish. COMPOSITION AND APPEARANCE Acrylic emulsion resin, mineral content, cellulose derivates, preservation agent and other additives. The resulting paste is a bright white colour and its consistency is adapted to its airless application. TECHNICAL CHARACTERISTICS • Dry extract : 68% • Density : 1,76 • COV : <1g/l APPLICATION SEMIN AIRLESSS 3 IN 1 can be sprayed with all kinds of Airless machines adapted to srpraying coatings. Recommended nozzle : 627. For optimum results, we recommend following this method : • Spray a first layer of the coating about 300 to 400 g/m2, to show up the defects on the surface. Spray at a distance of about 80 cm from the relevant surface • Check over the surface carrefully

TECHNICAL DEFINITION CE 78 PERFECT’LIGHT is a lightweight ready-mix paste specially formulated for jointing mitred-edge plasterboards in association with plaster tape. COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightweight fillers, preservation agent and various adjuvants. The paste is white. COVERINGS. Plasterboard primer. Smoothing filler. REFERENCE DOCUMENTS • CE marking • DTU 25.41 and DTU 25.42 • NF EN 13963 • DoP PACK SIZE 20 kg buckets on covered pallet. STORAGE 12 months in original unopened packaging away from frost and high temperatures. APPLICATION Before actual jointing, fill any accidental gaps between boards and any other areas (spalls, deterioration of the surface etc.). Apply manually by «buttering» the mitred-edge using a 10 or 15 cm plaster spatula and then adding the tape Then add a finishing coat, allow to dry and finish to hide the tape. Also hide the screw heads. For projecting vertical edges, use reinforced tape.

Vous recevrez ce savon de 100g conditionné dans son étui recyclable Ce savon surgras à 10% est réalisé à base de lait de chèvre, de la chèvrerie Florentin basée à Aboncourt-sur-Seille. Ce savon est très doux pour la peau, grâce au lait de chèvre et à l'huile d'argan bio. Il contient également de l'argile blanche permettant de nettoyer la peau tout en douceur Ce savon ne contient pas de parfum ni d'huiles essentielles, c'est pourquoi il peut être également utilisé par les enfants et les femmes enceintes

Vous recevrez ce pack emballé et prêt à offrir. Idéal pour un cadeau de naissance ou simplement pour se faire plaisir et prendre soin des peaux sensibles de notre bébé 100% naturel et fabriqué à la main. 1 sachet de 100 g de paillettes de savons pour réaliser 8L de lotion pour le change des bébés 1 bouteille pour la préparation de la lotion 1 sachets de 200 g de minis savons "mes premiers savons" 12 lingettes réutilisables fabriquées à la main. Tissu très doux, fabriqué à partir de pulpe d'eucalyptus. Son procédé de fabrication innovant en fait un produit très respectueux de l'environnement. Sa structure est naturellement respirante et permet de réguler l'humidité et la température. Tissu idéal pour les peaux fragiles

La crème est conditionnée en flacon airless de 50 mL Chamomilla recutita flower water*, Aqua, Simmondsia chinensis seed oil*, Corylus avellana seed oil*, Cetearyl alchohol, Glycerin, Polysorbate 60, Parfum, Dehydroacetic acid, Helianthus annuus seed oil, Tocopherol, Benzyl alcohol issus de l'agriculture biologique Crème de jour, à l'huile de noisette bio et à l'huile de jojoba bio, convient pour tous les types de peaux

100 g de copeau de lotion seule, sans bouteille. Vous pouvez retrouver le pack complet également sur notre site internet Découvrez notre lotion pour bébé. Rien de plus simple, juste à diluer les paillettes dans de l'eau. 100% naturel, très économique, ingrédients bio, sans conservateur, sans parfum Un sachet permet de faire 8L de lotion! 1 sachet de 100 g de paillettes de savons pour réaliser 8L de lotion pour le change des bébés Vendue sans la bouteille!

Lot de 12 lingettes réutilisables avec leur ruban pour pouvoir les accrocher facilement 12 lingettes réutilisables fabriquées à la main. Fabriquées à base d'un tissu très doux, issu de pulpe d'eucalyptus. Son procédé de fabrication innovant en fait un produit très respectueux de l'environnement. Sa structure est naturellement respirante et permet de réguler l'humidité et la température. Tissu idéal pour les peaux fragiles

Déodorant fabriqué à la main, à base d'ingrédients d'origine naturelle et bio. Ce sont des déodorants sous forme de stick. Dans le respect d'une démarche zéro déchet, les sticks sont en carton. Leur contenance est de 100 ml soit 2 fois plus gros que la majorité des déodorants, pour une utilisation toujours plus longue.Ils existent en 3 parfums, fleur de peau, citron et bergamote bio et pour homme Charbon et Cèdre. Déodorant solide de 100 ml Fabriqué à la main Fabriqué en France Vegan et non testé sur les animaux Régule le niveau de transpiration Hydrate et ne pique pas la peau Ralenti la repousse du poil Biodégradable Convient aux peaux sensibles, aux femmes enceintes et allaitantes (pour Fleur de Peau) Sans alcool, sans sel d’aluminium, sans huile de palme Parfait pour le voyage, autorisé en bagage cabine Économique, environ 3 mois pour 100 ml Emballage recyclable